![how to reprogram a cisco receiver without cable how to reprogram a cisco receiver without cable](https://www.mdpi.com/electronics/electronics-09-00040/article_deploy/html/images/electronics-09-00040-g019.png)
- HOW TO REPROGRAM A CISCO RECEIVER WITHOUT CABLE HOW TO
- HOW TO REPROGRAM A CISCO RECEIVER WITHOUT CABLE SERIAL
The settings are outlined here with a screenshot from PuTTy as an example.Īt this point, the cable is complete and ready for testing. Modify the settings of your terminal application. The cable is ready and you need to attach the RJ11 connector and crimp it as shown in the image. Make the cut another 0.25in (6mm) down into the sheath as shown in the image. This is done so the crimp is on the sheath, not the wires. Reduce the width of the sheath in order to allow the sheath access the RJ11 clip. Make the cut as square as possible so that the three wires are exactly the same length as shown in the images. Trim the ends of the red, orange, and green wires so they are approx 0.25in (6mm) long. The remaining wires are red, orange, and green as shown in the image. Trim the wire sheath, leaving approximately 0.5 inch (12mm) of wire exposed as shown in the image. The first step is to cut off the RJ45 terminal from the cable as shown in the image. Connect and Crimp the RJ11 Clip Detailed Steps Remove RJ45 Clip from CCC
HOW TO REPROGRAM A CISCO RECEIVER WITHOUT CABLE HOW TO
The detailed steps in this document describe how to properly trim the cable. In order to fix this use a pair of scissors to trim the outside of the blue sheath. Without modification, the flat console cable sheath is too wide to fit inside the RJ11 terminal clip. The image here shows the blue sheath inside the RJ11 clip. In order to create a cable that is durable, the plastic sheath inside the plastic end before crimping. The RJ11 cable as shown in the section Pinout Explanation is functional however, with only 3 small wires that hold the clip to the cable it can easily break. Note: Review the section Pinout Explanation before you move forward.
![how to reprogram a cisco receiver without cable how to reprogram a cisco receiver without cable](https://i.ebayimg.com/thumbs/images/g/H4sAAOSwVVVhc4nJ/s-l225.jpg)
Note: The part ID for CCC is 72-3383-01 and they are sent with most Cisco devices. Obtain an RJ45 to DB9 flat CCC then convert the cable an RJ11 to DB9 phone console cable with the process outlined here. Always verify the RJ45 pin number prior to cutting. Note: It is possible the colors of the wires vary between versions of the CCC. On a 4-wire RJ11 connector pins 1 and 6 are empty. RJ11 pins are counted with the clip down, from left to The table and the two images here display the difference between the RJ45 and RJ11 pinout.Ĭonsole Cable with red, orange, and green wiresĬonnected to RJ45 pins 3, 4, and 6.
![how to reprogram a cisco receiver without cable how to reprogram a cisco receiver without cable](https://i.ebayimg.com/images/g/a5gAAOSwBJphWWnC/s-l1600.jpg)
The standard RJ45 to DB9 flat CCC pinout is different than the pinout of the RJ11. If your network is live, ensure that you understand the potential impact of any command. All of the devices used in this document started with a cleared (default) configuration. The information in this document was created from the devices in a specific lab environment.
HOW TO REPROGRAM A CISCO RECEIVER WITHOUT CABLE SERIAL
These models support an RJ-11 serial port. This document is restricted to specific hardware versions. The AUX port of a phone is as shown in the image.Ĭisco recommends that you have knowledge of these topics:
![how to reprogram a cisco receiver without cable how to reprogram a cisco receiver without cable](https://eu.dlink.com/-/media/product-pages/dsl/2751/dsl2751d1imagelback.png)
The RJ-11 port also serves as a serial console port to access the phone's terminal. Many Cisco IP Phones have AUX ports on the back that are used to connect Key Expansion Modules (KEM). This document describes how to make a Cisco Console Cable (CCC) for Cisco IP Phones.